There are three important concepts to remember for wind-resistant wall construction. Walls have to resist the uplift forces caused by the pull of the wind. Walls have to resist the shear forces that try to push the walls over. Walls have to resist the lateral force of the wind that tries to push the walls in and pull them away from the building. For uplift purposes, walls are the intermediate link between the roof and the foundation below. To resist uplift forces walls have to have a continuous load path that can be achieved through the use of metal connectors for wood frame construction or a combination of metal connectors, vertical and horizontal reinforcement, and a bond beam at the top of the wall for concrete masonry construction. Shearing forces Walls are also subjected to shearing forces that act in the direction the wind is blowing. As wind blows on a wall, the walls perpendicular to the wall the wind is blowing on, are subjected to these shearing forces and are called shear walls. Shear walls are inherently subjected to the shearing and sliding forces. Wood frame walls resist these shearing and sliding forces through the action of the wall studs, the wall sheathing (preferably plywood), and a specific nailing pattern. Concrete masonry walls resist these forces through a combination of concrete masonry units, mortar, and grouted and reinforced cells. As a result of the walls resisting the shearing forces and being fixed at the base, the walls are subjected to an overturning force, or the tendency to rotate over. For wood frame construction, this force is resisted through the use of a holdown or tensions tied down. Vertical reinforcement and grouted cells resist the overturning forces in concrete masonry construction. Wind Ready Walls Finally, walls have to be capable of supporting the push and pull from the wind. For wood frame construction, studs have to be sized and spaced accordingly to resist the lateral forces, and have to be securely supported at the top and bottom plates. Concrete masonry resists the lateral forces by using reinforcement in grouted cells.

Bob meets Gary Halzel putting the finishing touches on the master bedroom walls. Gary will be rag rolling the wall. He's putting on a coat of oil-based mixture over a latex finish trying to get a translucent effect. The oil-based mixture is oil-based paint, glaze, and paint thinner.

Doug Frueh of West Coast Drywall is in the bedroom applying a textured finish to the fiberglass-faced walls. He is using Magnum, a dry mix that is blended with water to the desired consistency then sprayed on the wall with an airless sprayer. The effect is a splattered, built-up texture that is allowed to sit for a couple of minutes before being knocked down with a plastic wedge trowel that evens out the surface but maintains the texture. This technique is fast and low moisture, making it a perfect finish for Florida construction. Frueh says he can complete a house in just a couple of hours.

Charlie and Bob discuss how important it is to determine where the load-bearing walls are when undertaking a major remodel. Charlie points out the doubled-up 18-inch Georgia-Pacific LVL that is now carrying the entire load of the sidewall and the roof. During the installation Charlie found serious termite damage at the bottom of the support post. Since the LVL (or any beam) is only as strong as the posts that support it, Charlie cut out the damaged piece and put a new pressure-treated pad in and then posted it up with 2 x4s to tie it all in and create a solid point of transfer for the load. Using studs Charlie also created some temporary supports for the second floor joist system while he replaced load-bearing walls with a triple LVL and a 4 x 6 post. This basically transfers the load down to the basement to a lally column which will go down onto a concrete pad. The LVLs are 1 3/4-inch by 9 1/4-inch by 11 feet long.

…angle. • For best adhesion, be sure to "tool" caulk, using your finger, a disposable spoon or a damp rag for latex caulks. • For better energy savings, caulk windows & doors on the inside AND outside. • Check around your home…

… When applying any type of latex coating, use only brushes…
…brushes, when you are applying latex paints, make sure you use…
…and can he used to apply both latex and oil-based or alkyd paints…
…sprayers are a good choice for interior painting; larger, wheel-around gasoline…

…surface material can he painted including surfaces like aluminum or vinyl siding. Likewise, if you are planning to do interior painting, take a hard look at the rooms you want to paint. What is the condition of the walls? Will repairs be necessary? Is…

…painted, there are certain color treatments that will look good on almost any home. A near-surefire approach when doing interior painting is to paint the walls a neutral color like beige, and the ceiling and trim white. In fact, if you keep the trim and…