Bob meets with Mark Van Sickle from Merillat who is installing hardware on the new semi-custom kitchen cabinets. The Merillat cabinet doors and face frames are solid cherry in a cider finish. The cabinet end panels can be specified by the homeowner or architect to either match the cabinet fronts or to be made of plywood. Mark has set up a drilling jig for drilling holes for hardware to keep all holes on the same 5-inch center. He shows us the contemporary profile stainless steel pulls that will be attached to the doors. This set of cabinets has an unusual setup; it consists of 3 wall cabinets stacked on top of each other and built up on a platform for a toekick. This is an unusual installation creating a whole wall of cabinets like a butler's pantry while saving money buy using standard overhead cabinets. Solid end panels will be added to cover the seams of the stacked cabinets. Bob and Mark move over to the other wall where they notice the orgonomics - the extra organizational features that can be added to cabinetry - including a built-in wastebasket, a pull-out for cooking oils, a sink tray for scouring pads and sponges, an under sink tote for cleaning supplies, and a dishtowel holder. The pantry unit also incorporates orgonomics with slide-out wire baskets that are easy to install and adjustable to different heights - perfect for dry goods, cans, and cereal.

Bob Vila takes us from the shower that will also have a toilet and lavatory, through the dressing area with space reserved for a bench and cubby space, two small closets, and a sink and vanity. Brad Brewster of Princeton Custom Cabinetry joins Bob for the installation of a LesCare vanity that will be floated 12 inches above the floor, using a cross-braced configuration on the side wall, and a full cleat for support along the back. The floating installation was necessary because of the desired height of the vanity and the pipes that were detected in the walls. Brewster shows Bob the glued-dowel construction of the cabinets and the undermount hardware from Blum that will make all fasteners and cabinet hardware invisible once installed. Ernie Wernecke of Princeton Custom Cabinetry installs the vanity that has been pre-cut to accommodate plumbing, inserts drawers that were marked when removed for easy installation, and snaps on the doors of this lichen-green Formica-faced vanity.

Bob watches Tim Berky cut the mortises for the hinges on the solid-core, cherry-veneer door from Woodport. Berky uses a Hinge Mate from Precision Tools to guide his cuts for the three hinge mortises on the door. The oil-rubbed bronze butt hinges from the House of Antique Hardware will match the decor, handles, knobs, and pulls throughout the remodeled space. Berky then uses a jig to cut the mortises on the jamb, checks for plumb, and attaches the hinges and doors.

Bob moves to the kitchen in the Melrose remodeling project and talks with Jay Martel from the International Association for Child Safety about kitchen safety for toddlers. Martel reviews new products that can help make the kitchen safe. Martel shows an adhesive latch to prevent a child from opeining the refrigerator. Martel then shows a product that magnetically latches cabinets and prevents pinching. When activated, cabinet doors will not open until a magnetic "key" is used. The product can be disengaged by adults with a flip of the switch. For stove safety, Martel recommends parents use the backburners with handles turned away to prevent children from spilling heated foods and liquids. Martel explains that dishtowels draped over the stove's oven handle often invite children to pull on them and should be removed to prevent an accident. Stove knob covers should also be put in place. Martel shows how electrical outlets can be replaced with sliding covers that automatically slide shut when electrical plugs are removed. Bob and Martel then move to the staircase to review baby safety gates that have been installed. Martel says nothing is more important for children's safety than installing gates at the tops of stairs. Martel shows how the swinging gate requires two motions to open, a squeezing action followed by lifting. Martel reviews how the gate has been properly installed with affixed mounting hardware and inswinging action.

…replacement windows and entry doors or kitchen cabinet remodeling or refacing, you can be confident…
…design consultation! Sears Kitchen Cabinet Remodeling and Refacing Your dream kitchen, created by Sears, featuring Kitchen Cabinet Remodeling or Kitchen Cabinet Refacing…

Over 21,000 residential and commercial plumbing products that are on hand and ready for same day shipping from our big network of warehouses scattered throughout the United States.

…noticeable cannot completely repair a piece that is damaged. Sink Limitations A drop-in or self-rimming sink is typically used with laminate kitchen counters. The raw edge around the sink must be sealed properly so water can't penetrate between…

…alternative was using steel. However, the laminated veneer lumber (LVL) manufacturing process…
…can reliably support large areas. Laminated veneer lumber is an engineered wood product…
…as plywood. The resulting parallel-laminated lumber out-performs conventional lumber…