View ChannelsFeatured: Finance
View ShowroomsFeatured: Radiantec - Radiant Solar Heating

BobVila.com

Home

Removing Mold

Get Adobe Flash Player to see this content.

Clip Transcript For:

Removing Mold

Here s another great tip from BobVila.com. Mold problems are present in about four out of 10 American homes. With the often prohibitive costs and dubious results of professional mold remediation, more and more homeowners are looking for ways to take care of mold problems themselves. If mold is affecting an area less than 10 square feet and your household doesn t include anyone who is very young, very old or immune-compromised, you can tackle the problem yourself if you re careful. First, consult the EPA s web site and read about the different levels of mold infestation and the levels of protection they require, both for you and for the rest of your house. Mold spreads by sending out millions of airborne spores. Disturbing a mold infestation can send the spores flying and make your problem worse and more widespread unless you seal off the area and protect yourself. Seal off any heat or air vents to the affected area, and install a window fan to pull air to the outside. Seal off the area with plastic sheeting taped over the doorway. Never touch mold with your bare hands, get it in your eyes or breathe it. Wear a disposable work suit or clothing you can throw away after the job is done. Wear a respirator, gloves and goggles, and shower well after you ve finished. Contrary to popular belief, you cannot kill mold with bleach. It might remove the appearance, but it won t get the roots, which will re-bloom in a matter of days, sometimes hours, if the area remains wet. In general, the best way to get rid of mold is to remove the affected materials altogether and rebuild. Removal is your only option if the moisture came from grey water or sewage. If the moisture source was clean, use a wet vac or steamer to remove wet or loose debris first and double-bag it in heavy trash bags. Then damp-wipe or scrub with detergent and water, but don t soak the surface. When it s thoroughly dry, vacuum again with a HEPA vacuum. Double-bag the vacuum contents and thoroughly clean or replace the vacuum s filter. You can dispose of the bags of debris with the rest of your trash. If the moisture problem that invited the mold in the first place has been fixed and the area remains completely dry, the mold may not re-grow. Find out more at BobVila.com: the ultimate home improvement web site! 2008 BobVila.com

More Videos »Related Videos

Direct Vent Fireplaces for Heat and Ambience

Bob visits a Heat n' Glo showroom where Ross Morrison shows him a variety of direct-vent gas fireplaces. With a sealed glass chamber there is no interplay of of room air�no products of combustion will get into the room and it doesn't use any of the the room's already warm air for combustion. The fireplace inserts come with ceramic fiber logs. When the flames hit the logs they produce a nice glow. The logs are light, unbreakable, and last a lifetime. Ross shows Bob the 6000 TRXI, a premium model that is rated as a furnace. It has a beautiful masonry appearance inside and a pumps out enough BTUs to heat a 1200 - 1500 sq. ft. house. The fireplace also offers the option of turning the flames down or off or opening the climate control damper to cut the heat by one half.

Direct-Vent Fireplace Installation

Jack Murdock from RMI and Craig Ryans from Vermont Castings of Mississauga, Ontario, demonstrate how simple it is to have gas appliances and heat in a rural location. With a 500 gallon underground or exterior tank, enough fuel is stored on site for most common uses and requires just a few fill ups a year. The stove being installed, a Vermont Castings product, uses a direct vent technology that draws no interior air to aid in combustion. The unit pulls air in from outside through a cylinder pipe and releases exhausts outside as a typical furnace would. Gas appliances and heat function during power failures, although electric fans that circulate the heat will not work without an auxillary power supply. The fireplace installed in the Modular Mountain Retreat project home will provide 30,000 BTUs of heat. A realistic ceramic grate burner and ceramic logs enhance the fireplace�s look.

Vent Pipe Installation

A vent pipe is installed in the ranch's roof. A hole is cut and a shield added to created a weather tight seal around the pipe and roof shingles. Down in the basement the new vent pipe is added to the home's existing plumbing.

Multi-Zone HVAC System

Bob meets with Mark Gallivan from Sears HVAC and Brent Morin from Morin Mechanical Services to review the heating system installation at the modular home project. The high efficiency, state of the art Hydro-Air system uses components of a traditional boiler, humidifiers, variable speed fans, electronic air cleaners and three exterior condensing units. Carrier manufactures many of the heating unit�s components including the boiler. The boiler produces hot water for both a forced air unit and a baseboard radiant heating system. The forced air unit allows for a consistent level of humidity in the house, that traditionally radiant-only units cannot accomplish, plus it receives the efficiency of radiant by employing a baseboard system. This gives the home�s occupants a more comfortable living environment. There are seven zones employed in the home�s heating and cooling system. The cast aluminum heat exchanger in this unit transfers heat three times faster than a traditional heat exchanger. The boiler uses a direct venting system that takes air directly from outside and vents it through a flue located in the center of the intake vent. This means no combustion gases are being mixed with the home�s interior air. The system�s zones can be turned on or off as needed, providing an added level of efficiency if the entire home is not being occupied at a given time.