View ChannelsFeatured: Finance
View ShowroomsFeatured: Radiantec - Radiant Solar Heating

BobVila.com

Home

How to Fix a Clogged Drain

Get Adobe Flash Player to see this content.

Clip Transcript For:

How to Fix a Clogged Drain

Here's another great tip from BobVila.com. Don t let a drain clog slow you down; it s usually an easy fix. A partial clog can be cleared by cleaning out the drainpipe. Older plumbing can be damaged by using harsh drain chemicals, so opt for a naturally biodegrading drain cleaner or use this homemade solution: pour a half cup of baking soda down the drain, then slowly add a cup of white vinegar. Cover the drain for five minutes, then flush with a gallon of boiling water. Some clogs call for a plunger. The key here is to create a vacuum. If you re working on the kitchen sink, you need to clamp off the dishwasher hose and seal the drain openings in the other sink basins. If it s the bathroom sink or tub, plug the overflow opening with a wet rag. With at least a couple inches of water in the basin, plunge rapidly several times, pulling up sharply at the end to move the clog. You may need to do this several times. If plunging doesn t clear the clog, use an auger. If your drain opening is obstructed, sometimes a coat hanger wire with a small hooked end will bring up the clog. You can also detach the trap under the sink with a plumber s wrench in order to get at the clog or to rescue anything you ve lost down the drain. If you don t see an improvement in drainage after all of that and especially if more than one drain is slow in your house you should consult a plumber since the problem could be caused by blocked or improper venting of the wastewater system. Find out more at BobVila.com: The ultimate home improvement web site! BobVila.com 2008

More Videos »Related Videos

How to Unclog a Blocked Tub Drain

Tub drains may clog from time to time, but unclogging them is an easy process with a few quick solutions.

How to Clear a Blocked Sink Drain

Clearing a blocked sink drain requires only few basic tools and a little elbow grease.

Spraying on and Painting a Heat-reflective Pool Deck Surface

Don Humphrey is spraying a cement and polymer mix from Innovative Concrete Technology called Texture-Krete 2000 onto the pool edge and deck in Punta Gorda, Florida. He moves in a circular motion to splat the cement mix onto the deck. As the gloss begins to leave the spots, a crewmember follows behind to knock it down with a trowel. This removes the pointy tops but leaves a 1/16-inch stucco pattern to the pool deck to make it easy to walk on. The deck is cleaned and scratched to remove any rough points before Humphrey and his crew apply an acrylic paint to the textured deck surface. The key to a well-sealed surface is to roll the paint firmly into all the nooks and dips in the surface. Bob talks about the embedded deck drain set in the concrete that is pitched slightly away from the pool. Excess water and dirty deck water drains away from the pool and is carried off to the sides of the pool deck by the deck drain. Humphrey applies two coats of paint and a topcoat for protection. The deck can be maintained with gentle soap-and-water washing to prevent any white spots from drying chlorine on the painted surface. Humphrey says the paint should last three to five years before it is redone. One key to maintaining the surface is to avoid abrasive cleaners or power washing. Should any mold or mildew attack the surface, Humphrey suggests using a mild bleach-and-water solution to kill the mold. The oyster color the homeowners have selected should wear well and stay cool in the hot Florida sun. Editor�s Note: The deck surface product with cooling properties used in this application was not Kool Deck from Mortex.

Installing Systems to Keep Water Out of the Basement

Larry Janesky of Basement Systems reviews the work being done to cut a drainage trench in the concrete around the perimeter of the basement floor. Water will be channelled through the trench to a sump, where it can be pumped out of the home. The sump hole was dug at the lowest spot in the basement as determined by laser level. CleanSpace is being installed over the walls as a vapor barrier to drain water from the walls to the drainage system. It is possible to install CleanSpace in crawlspaces as well as in basements to prevent water buildup in underground walls and eliminate rot and mildew. Janesky recommends taking these two steps in securing the drainage of a home and to secure against all outside air leaks. The final step is to dehumidify the crawlspace. Janesky points out a corner of the basement where the Thermal Dry Wall System has been installed. This product goes behind finished walls and drains water like CleanSpace but also reflects heat generated in the basement back into the basement. Janesky then shows a portion of the floor where the Water Guard Drainage System has been installed in the drainage trench and secured with cement.