BobVila.com

Here's a technique professional carpenters use to conceal nails or screws: use wooden plugs. Use a dowel bit to drill out the plugs. Dip each plug in carpenter's glue, and tap it into place over the nail or screw. Let the glue dry, then shear the plug off with a wood chisel. Sand the suface smooth and apply your finish.

When putting up shutters, the key is to have good, sturdy hardware. Look for pressure treated wood shutters for exterior use. To have operable shutters, the shutter dogs and hinges need to be sturdy (and of high quality). After marking the location for the hinges, drill pilot holes for the screws. Then screw the hinges and other hardware in place. Hang your shutters and test the fit.

Before you hang that nice big bathroom mirror, be sure you keep these things in mind. You'll need to support the bottom edge by screwing in a length of j-channel. To protect the mirror's silver backing, cover the screw heads with duct tape and be sure to use specially-designed mirror mastic, since other adhesives can eat away the back and leave spots.

Here s another great tip from BobVila.com. Get a jump on the hot weather by making sure your room air conditioner s up to the challenge. Before you pull it out of storage, consider the age of your air conditioner. Efficiencies have improved so much that replacing an old clunker from the 70s with a new 10-seer unit could cut your cooling costs in half. Regardless of age, all units need maintenance every season and about once a month during the season. First, unplug the unit and see your manual for instructions on discharging the capacitors to avoid a shock. Dirt is your air conditioner s worst enemy. Clean out the drain ports with a length of wire. Vacuum the evaporator and condenser coils and gently straighten any bent fins with a fin comb, which you can get at most hardware or plumbing supply stores. Remove the filter and wash and dry it thoroughly or replace it with a new one if it s the disposable kind. Run the unit for a few minutes to see how it performs. If the fan s making noise, try tightening the blade s set screw as well as the bolts that hold the fan unit to its housing. If the power cord, switch or thermostat is worn or faulty, you can replace it without having to buy a new unit. The coils, compressor and motor are all sealed and should be repaired by a professional. On the bright side, if you do this check early, you won t be put on someone s waiting list in 90-degree heat! Find out more at BobVila.com: the ultimate home improvement web site! 2008 BobVila.com

Here's another great tip from BobVila.com. Now s a great time to do a whole house electrical inspection, and you can do this kind yourself. Make a checklist of the rooms in your home. Then take a tour of your outlets and appliances, turning everything on and plugging something into each outlet. Is every outlet covered by a plastic plate? Are any damaged or loose? Do they all work? Do you have extension cords running around the room? Where would it help to have an additional outlet? Put your hand on the wall around each outlet to check for warmth. Look for flickering lights and sniff for strange smells. If you ever see sparks or smoke, call an electrician immediately. Make a note of any outlets that aren t grounded: the kind that accommodate three-pronged plugs. In the kitchen and bath and outdoors, note any outlets that aren t equipped with ground fault circuit interruptors. They re required by code in many states. They ll protect you and your family from the hazards that are present anywhere water and electricity come close. With your checklist, a licensed electrician can make quick work of upgrading your outlets and checking your wiring system for safety. This work can cost a couple of thousand dollars but it s well worth it, especially if you re still changing those old screw-in fuses every time you use the toaster and the hair dryer at the same time! Find out more at BobVila.com: The ultimate home improvement web site! BobVila.com 2008

Here s another great tip from BobVila.com. Although the two words are often used interchangeably, sheetrock is actually a brand name for drywall, which is gypsum sandwiched between two sheets of paper or, more recently, between two sheets of fiberglass. Any way you say it, drywall makes finishing walls very practical. For large jobs or those with very high ceilings, hire a pro. But most smaller jobs can be tackled by do-it-yourselfers. Before you get started, run the side of a hammer head along the framing to check for uneven surfaces or any protruding staples or nails. The tools you ll need are a straightedge and measuring tape for sizing your pieces, a utility knife for scoring and snapping, and a keyhole saw or rotary tool for cutting holes for outlets and windows. While some pros still attach drywall with nails, most find it easier to use an electric drill and that wonderful multi-purpose fastener, the drywall screw. You ll need about a pound of nails or screws for every 5 sheets of drywall. Metal corner beads go on all outside corners; inside corners get taped along with the joints between panels. Using pre-mixed joint compound is easier and less messy than mixing your own. You want a mix that s not too quick-drying if you re a beginner so you have a grace period to work in. Pros use about 5 gallons of compound for every 100 square feet, but you may need more depending on your level of experience. Installing drywall involves a series of short steps over a 3- to 4-day period. Follow the steps on BobVila.com for taping and finishing joints, and be sure to wear safety gear and a dust mask while sanding. If you re doing a ceiling, get a helper or a drywall lift. Find out more at BobVila.com: the ultimate home improvement web site! 2008 BobVila.com

This project initially began as a basement refinishing project and has grown into a project for a growing family. The front porch of the Melrose home was in need of repair. This involved not just the decking but the structure underneath, which had suffered rot and insect damage. The finished wood deck features Ipe, a renewable tropical wood from Everlasting Hardwoods. This wood is one of the best decking products available but does not nail easily. To get around this, Tiger Claw hidden deck fastening system is used to keep the wood in place without any obvious face nailing. Don Martel of Tiger Claw explains how the product is installed. The version being used is designed for extremely dense materials, like the Ipe decking used here. The fastener attaches to the edge of the board. A screw is then drilled through the fastener into the joist. The fastener holds the board and the screw holds the fastener in place. The fastener is coated in black oxide so it is not visible between the seams of the deck. Every Tiger Claw kit comes with a installation tool. The fastener is insterted into the tool, placed against the board, and hammered into place. Using a hammer board, the next board is put into place with one tap. The fastener from the previous board grips it tight as it is tapped in. The Ipe decking is not only strong but naturally insect-resistent without the use of any chemicals.